×
Subtotal: $0.00
View Cart
?
Support Chat powered by ChatGPT
Responses are generated by ChatGPT and may not be completely accurate.

Sure-Fi Wiegand App Notes

  1. Scope
    1. This document outlines the connections that are required to wire the Sure-Fi Wiegand Bridge to the DoorKing® 1838 Multi-Door Access Controller as well as to a DoorKing® 2358 Tracker Expansion board.
  2. Summary:
    1. The Wiegand Bridge interfaces directly with the DoorKing® 1838 Access Controller on the Wiegand Inputs 1 & 2 that are on the Auxiliary Terminal when interfacing directly to the Wiegand device at the access entry point when a Tracker Expansion Board is not used. If a DoorKing® 2358 series Tracker Expansion Board is being used between the DoorKing® Access Controller and the Wiegand device at the access entry point, then the Wiegand Bridge must be connected at the point that is between the Tracker Expansion Board and the Wiegand device that is at the access entry point. NOTE: The Sure-Fi Wiegand Bridge cannot be used with the DoorKing® 2358 series Tracker Expansion Board at the Communication Data Output ‘Data 1’ and ‘Data 2’ terminal connections on pins 28 and 29 of the Tracker Expansion Board. The Wiegand Bridge must be connected at the Wiegand Input Data 0 / Wiegand Input Data 1 on the terminal connection pins 6 and 7 of the Tracker Expansion board.
  3. References (current version unless otherwise specified)
    1. DoorKing® 1838 Multi-Door Access Controller Series Installation/Owner’s Manual
    2. DoorKing® 2358 series Tracker Expansion Board Installation/Owner’s Manual
    3. Sure-Fi Wiegand Bridge Operators Manual Doc #PI0026
  4. Procedure
    1. When the DoorKing® 2358 series Tracker Expansion Board is not being used:
      1. This example shows the DoorKing® Wiegand Input 1/Relay 1 combination connected to control a Door-Strike, Mag-Lock, or Gate Operator, but the Wiegand Input 2/Relay 2 combination can also be connected in the same manner. The Wiegand Bridge interfaces directly with the DoorKing® Access Controller on the two Wiegand inputs on the Auxiliary Terminal when interfacing directly to a Wiegand device at the access entry point
        1. See Figure 1 for the Wiegand Controller Interface wiring.
        2. See Figure 2 for the Wiegand Remote Interface if connected to a DoorStrike or Gate Operator.
        3. See Figure 3 for the Wiegand Remote Interface if connected to a Mag-Lock
    2. When DoorKing® 2358 series Tracker Expansion Board is being used:
      1. This example shows how to connect the Sure-Fi Wiegand Bridge to the Tracker Expansion Board to provide a wireless-bridge for the Wiegand, Output Relay, and a REX button out to the remote access entry point for control of a Door-Strike, Mag-Lock, or Gate Operator.
        1. See Figure 4 for the Wiegand Controller Interface wiring.
        2. See Figure 5 for the Wigand Remote Interface if connected to a DoorStrike or Gate Operator.
        3. See Figure 6 for the Wiegand Remote Interface if connected to a Mag-Lock

 

Figure 1: Wiegand Bridge CONTROLLER Interface connected directly to the Wiegand 1 / Relay 1 of the DoorKing® 1838 Access Controller. See Figure 2 or Figure 3 for REMOTE side connections.

Figure 2: Wiegand Bridge REMOTE interface connected at the access entry point with a Door-Strike or Gate Operator. See Figure 1 for CONTROLLER side connections.

Figure 3: Wiegand Bridge REMOTE interface connected at the access entry point with a Mag-Lock. See Figure 1 for CONTROLLER side connections.

Figure 4: Wiegand Bridge CONTROLLER Interface connected to the DoorKing® 2358 series Tracker Expansion Board. See Figure 5 or Figure 6 for REMOTE side connections.

Figure 5: Wiegand Bridge REMOTE Interface connected at the access entry point with Door-Strike or Gate Operator. See Figure 4 for the CONTROLLER side connections.

Figure 6: Wiegand Bridge REMOTE Interface connected at the access entry point with Mag-Lock. See Figure 4 for the CONTROLLER side connections.

 

FCC and Industry Canada Regulatory Statements

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by manufacturer could void the user’s authority to operate the equipment.







 

IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.



 

Industry Canada

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.

 

IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actioner cet équipment.

47 CFR 15.105- FCC

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help. 

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Important Note:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

 

Note Importante: (Pour l’utilisation de dispositifs mobiles) Declaration d’exposition aus radiations:

Cet équipement est conforme aux limites d´exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipment doit être installé et utilisé avec un mimimum de 20 cm de distance entre la source de rayonnement et votre corps.

 

Warranty

The warranty period of this product is 5 years from purchase date, beginning from first power up of the device after purchase. During this period, if the product does not operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Sure-Fi, Inc. This warranty does not extend to the product casing which can be damaged by conditions outside of the control of Sure-Fi, Inc.

EXCEPT AS SET FORTH ABOVE, SURE-FI, INC. MAKES NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF SURE-FI, INC., EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. SURE-FI, INC SELLS THE GOODS TO BUYER ON CONDITION THAT SURE-FI, INC. WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT SURE-FI, INC. SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD SURE-FI, INC. HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS.